Home › Services › AC not turning on
Problem guideAC will not turn on: the safe checklist before you call
A system that does nothing at all is usually an electrical supply or control problem, not a refrigerant problem. The safe checks are quick: thermostat power, breakers, the outdoor disconnect, and the float switch that protects against drain overflow. Anything beyond that belongs to a technician with a meter.
- Independent referral service
- No charge to homeowners
- One contractor receives your request
- No ratings or paid placements
Request a callback
Describe the symptom and your ZIP. One contractor receives it if one serves your ZIP.
Symptoms
- No fan, no outdoor unit noise, no cool air.
- The thermostat screen is blank or unresponsive.
- The outdoor unit may hum briefly and stop.
- A breaker may be tripped or the outdoor disconnect may be pulled.
Safe checks you can do
- Replace the thermostat batteries if it uses them, or confirm the thermostat is powered by the air handler.
- Find the air-handler breaker and the condenser breaker in the main panel. Reset a tripped breaker once.
- Check the outdoor disconnect box near the condenser; the pull-out handle must be fully seated.
- Look for a float switch on the drain line or drain pan. A full pan lifts the switch and cuts the system off; empty the pan and clear the drain before resetting.
- Confirm the service switch on the side of the air handler is ON.
- If the system uses a smart thermostat, check the app for an offline status or a schedule hold.
Likely causes
- Tripped breaker or pulled disconnect — The simplest and most common cause, especially after a storm or a power flicker.
- Float switch open — A clogged condensate drain fills the pan, the safety switch opens, and the system shuts down to prevent water damage.
- Dead thermostat or transformer — A failed low-voltage transformer or a thermostat without power leaves the system with no call for cooling.
- Failed capacitor or contactor — The outdoor unit tries to start, hums, and trips its internal protection.
- Open safety switch or pressure control — High or low refrigerant pressure, a dirty filter switch or a condensate switch can hold the system off.
- Failed control board — No low-voltage output to the contactor even though the thermostat calls.
What a repair involves
The technician verifies line voltage at the disconnect, control voltage at the transformer, and the thermostat call at the control board. From there the fault is usually a switch, a low-voltage component, a capacitor or a board. Repair times are short once the circuit is traced.
Typical South Florida cost ranges
| Work | Published typical range | Notes |
|---|---|---|
| Diagnostic or service visit | $69–$250 | |
| Capacitor replacement | $150–$400 | |
| Contactor or relay | $100–$450 | |
| Thermostat replacement | $100–$500 | Includes basic programmable and smart thermostats; premium models cost more. |
| Circuit board replacement | $200–$800 |
Source: AC Service Pro (South Florida contractor cost guide), published 2026-07-13; Koala Coolin (South Florida contractor cost guide), published 2026-07-12. Both guides publish installed price ranges for South Florida; neither states its sample size. These are ranges, not quotes. The contractor sets the actual price after inspecting the system, and you approve it before work begins. See the cost guide methodology.
Seasonal context
Power flickers during South Florida storm season are a frequent cause of a system that will not restart. If the breaker resets and the system still does nothing, stop resetting it and request service.
Where to go next
Find your city · Cost guide methodology · What to check before you call · All services
How a request is handled
Your request includes the symptom, your ZIP code, how soon you need help and the best time to reach you. If a participating contractor covers your ZIP, that one contractor receives it.
If no participating contractor covers the ZIP yet, we tell you and your request is not shared with anyone else.
We do not promise an arrival time. The contractor confirms availability with you directly.
Questions
Why does my AC breaker keep tripping?
A breaker that trips more than once points to a failing compressor, a shorted fan motor, a bad capacitor or a wiring fault. Repeated resets can damage the compressor, so stop after the first retry.
The thermostat is blank. Is that always a thermostat problem?
No. A blown low-voltage fuse or a failed transformer produces the same blank screen. A technician can tell the difference in a few minutes.
Can I reset the system at the outdoor disconnect?
You can confirm the handle is seated. Do not pull or reinsert it repeatedly while the system is calling for cooling.
Request a callback
One contractor, if one serves your ZIP. No charge to you.
Request a callback
Tell us what is wrong. If a participating contractor serves your ZIP code, your request goes to that one contractor.